Enclosure Material:18g steel, with lock and tamper
Expansion:Includes mounting standoffs for two point expansion modules (I8, I8-CSI, R8 or RM-4)
Environmental: 0° to 50° C (32° to 122° F)5 to 95% relative humidity, non-condensing
Weight with Enclosure :4.2 kg (9.3 lbs)
Electrical
Power Requirements:12 VDC (-15/+20%) or 24 VDC (-15/+25%), auto-sensing Board only: 200 mA@12 VDC or 100mA@24VDC; Max. of 3.8 A@12 VDC or3.1A@24 VDC for board plus all attached devices.
Optional PoE Plus Module
Standards Supported:PoE (802.3af), 12.95 W min; PoE Plus (802.3at), 25.5 W min Power negotiation uses two-state physical discovery (LLDP-MED not supported)
PoE Standard Selection:Jumper-selectable
Lock Power Voltage:Jumper-selectable between 12 and 24 VDC; applies to all four outputs Power Available for
Attached Devices2:PoE: 600 mA@12 V or 300 mA@24 V PoE Plus: 1400 mA@12 V or 700 mA@24 V
Heat Dissipation:90 BTU/HR typical
Memory and RTC Backup:Four standard AA alkaline batteries provide automatic database backup to flash memory
Battery Life:Five years (estimated – without power interruptions)
System Memory
Memory:64 MB RAM, 128 MB flash EEPROM
Cardholder capacity
One clearance, one card/person, ten-digit cards :400,000
Ten clearances, one card/person, ten-digit cards:230,000
One clearance, five cards/person, ten-digit cards:130,000
Ten clearances, five cards/person, 40-digit cards :85,000 Note – Memory allocation is dynamic and shared between cardholders, event storage, and configuration information.
Network Communications
Ethernet Ports:One, 10/100Base-T
Network Encryption:AES 256-bit, FIPS 197
Readers
Number of Readers Supported : One, two, or four Types of Readers Supported . Wiegand and RM (RM only for readers 3 and 4) Reader Technologies
Supported:Multi-Technology, Proximity, Smart Card (incl. PIV II & TWIC), Wiegand and Magnetic Stripe (RM only)
Maximum Distance to Door:RM: 1,219 m (4,000 ft); Wiegand: 150 m (500 ft)
Reader Power Available:12 VDC, 1.5 A total (including aux power and RM port power)
RM Bus Communications :Three ports, RS-485 half duplex, two wire, plus optional two wires for device power (One-reader model does not have RS-485 ports)
Inputs
Supervised Inputs:Eight, single or double-resistor (One-reader model would have four)
Fire Alarm Interlock Inputs:Two, fire alarm input and manual keyswitch override (supervision supported)
Additional Inputs:Tamper switch, power fail, and low battery
Input Expansion:Up to 32 additional inputs using I8 input modules on RM bus (64 additional with 4-reader model)
Auxiliary Power Available :12 VDC; two (350mA each) (One-reader model has one port)
Outputs
Outputs :Four, individually configurable via jumper as power sourcing (wet), or dry contact relay (one-reader model has two)
Output Power, Wet:12V or 24 VDC, 0.75A (If iSTAR Edge powered locally, output voltage follows input voltage. If using PoE/PoE Plus, jumper-selectable between 12 and 24 VDC) Output Protection,
Per Output:PTC resettable fuse, 0.75 A, snubber, transzorb
Output Rating, Dry:30V AC/DC, 3 A
Output Expansion:Up to 32 additional Form C relay outputs using R8 output modules on RM bus (up to 64 additional with 4-reader model)